Danke für das Bild. Sehe ich zum ersten Mal sowas. Hat mein 88er Suburban sowat auch? Ich muß bei 2 Türen nämlich auch die Pins neu machen.
ACHTUNG wichtiger Hinweis ! |
Bei Neuregistrierungen wird die Aktivierungs-Email immer
häufiger im SPAM Ordner zugestellt !! Besonders häufig passiert dies bei Usern die folgende Emailanbieter verwenden: |
- web.de - hotmail |
- gmx - yahoo |
- icloud - aol |
Wer sich neu registiert und nicht
innerhalb von ca. 60 min eine Aktivierungs-Email erhält, bitte den SPAM Emaileingang kontrollieren. Nicht aktivierte Accounts werden automatisch nach 7 Tagen gelöscht ! |
-
-
Moin
Das Teil der Begierde: Door Spring Compressor Tool GM (DST-GM)
von: Hot Rod Auto Supply.com
View tool user guides: Bitte melden Sie sich an, um diesen Link zu sehen.
Ein mehr an Adresse habe ich nicht mehr.
Rolf
-
Ist mit Tür Pin der Aussenschliessdorn gemeint?
Ich hab auch das Problem, dass meine hintere Tür etwas "rappelt" und Spiel hat, wenn ich über Unebenheiten fahre... -
Nein, es ist sind die 2 Pinne gemeint, die die Tür im Scharnier halten.
-
Wenn die ausgeleiert sind, habe ich dann den oben beschrieben Effekt?
Weisst du zufällig, wie das Teil bei Rockauto heisst? -
Ich glaube das heißt Hinge Pin oder Hinge Bushing.
P/N
Description
Qty/Door
15025842
Bushing (Lwr Hinge, Lwr, Upper Hinge, Upper) (Teflon)*
2
15025841
Bushing (Lwr Hinge, Upper, Upper Hinge, Lwr) (Teflon)
2
16632193
Bushing (Lwr Hinge, Lwr, Upper Hinge, Upper) (Bronze)
2
16632192
Bushing (Lwr Hinge, Lwr, Upper Hinge, Upper) (Bronze)
2
88891731
Hinge Pin
2
88891766
Hinge Spring
1
25640501
Hinge Pin Retainer
2
15025840
Kit, Severe Service, Frt Door Hinge**
1
*Also Included in Severe Service Kit, P/N 15025840. Not installed in service hinge assemblies.
**Includes Teflon® bushings, anti-chucking spacer, spacer fasteners and instructions. -
Top! werd ich mal ordern und sehen, wie sich die Tür dann verhält. Vielleicht mache ich zur Vorsicht alle anderen auch mal mit.
-
Der Stift ist der Pin und die Hülse die ins Loch kommt ist der Bushing .
greetings
Midnightflyer -
Und wie werden die Mistdinger eingebaut? Tür muss raus, dass kann ich ja noch nachvollziehen.
Werden die verschraubt? Verklemmt? -
1999 Chevrolet/Geo Tahoe - 4WD
Door Replacement
1. Apply cloth-backed tape to the door and the body pillar.
Bitte melden Sie sich an, um dieses Bild zu sehen.2. Remove the lower hinge pin retainer.
3. Remove the lower hinge pin by completing the following steps:
A. Use a pair of locking pliers in order to grasp the pin.
B. Use a soft-faced hammer in order to drive out the pin.
IC. nstall a bolt through the lower hinges in order to temporarily hold the door in place during the removal of the upper hinge.
4. Remove the upper hinge pin retainer.
5. Remove the upper hinge pin.
6. Remove the bolt from the lower pin hole.
7. Remove the door from the vehicle.Bitte melden Sie sich an, um dieses Bild zu sehen.
Install the door to the vehicle.
Install a bolt through the lower hinge pin holes in order to temporarily hold the door in place.
Install the upper hinge pin with the pointed end of the pin pointing up.
Install a new hinge pin retainer.
Remove the temporary bolt from the lower hinge.
Install the lower hinge pin with the pointed edge of the pin pointing down.
Install a new hinge pin retainer.
Lubricate the bushing with engine oil.
Remove the cloth backed tape from the door and the body pillar.Door Replacement - FrontDoor Hinge Spring Compressor (Spezialwerkzeug Nr. J36604 )
Bitte melden Sie sich an, um dieses Bild zu sehen.Caution
Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.Disconnect the negative battery cable.
Remove the cowl side vent cover.
Remove the wire harness connectors under the instrument panel completing the following steps:
Remove the receptacles from the wire harness.
Remove the retainer from the wire harness grommet.
Remove the rubber conduit from the door pillar by pushing the rubber conduit from the vent cover side.Insert the blades of the J 36604 between the spring coils.
Turn the barrel nut in order to compress and hold the spring during the removal.
Bitte melden Sie sich an, um dieses Bild zu sehen.Remove the lower hinge pin by completing the following steps:
Using a pair of locking pliers, grasp the pin.
Using a soft-faced hammer, drive out the pin.
Install a bolt through the lower hinges in order to temporarily hold the door in place during the removal of the upper hinge pin.Bitte melden Sie sich an, um dieses Bild zu sehen.
Remove the upper hinge pin retainer.
Remove the upper hinge pin (2).
Remove the bolt in the lower hinge pin hole.
Remove the door from the vehicle.Bitte melden Sie sich an, um dieses Bild zu sehen.
Install the lower hinge pin with the pointed edge pointing down.
Install the new lower hinge pin retainer.Using the J 36604 , install the door hinge spring.
Connect the harness connectors by completing the following steps:
Install the rubber conduit through the body pillar.
Install the retainer around the wire harness grommet.
Install the receptacles to the harness under the instrument panel.
Install the cowl side vent cover.
Connect the negative battery cable.
Lubricate the bushing with engine oil. -
Holy smoke... Ich spreche ja gut und viel auswärts, aber da muss ich mal in Ruhe ein paar Begriffe raussuchen 8-)
-
Bitte melden Sie sich an, um diesen Link zu sehen.
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!